Lite Magazines logo Lite MagazinesA little bit of everything, explained clearly
Home

How to Fix a Dripping Tap Without Calling a Plumber

A tap that drips once a second loses roughly 15 litres a day, which is about 5,500 litres a year, or eleven full baths you never took. That figure is annoying but survivable.

A kitchen tap taken apart on a worktop with the headgear, a rubber washer and an adjustable spanner laid beside the sink

A tap that drips once a second loses roughly 15 litres a day, which is about 5,500 litres a year, or eleven full baths you never took. That figure is annoying but survivable. The part that actually drives people to act is the sound at two in the morning, amplified by an empty steel sink into something that lands like a metronome.

Most dripping taps come down to one worn component that costs between 60 pence and 12 pounds, and replacing it takes twenty minutes once you know which component it is. The confusing part is that there are three completely different mechanisms sold under the same word, and the fix for one does nothing for the others. Working out which one is in your kitchen is most of the job.

Work out which mechanism you have

Turn the handle from fully off to fully on and count. If it takes two or three full rotations, you have a compression tap, the old design with a rubber washer pressed down onto a brass seat. If it travels a quarter turn and stops hard, you have a ceramic disc valve. If it is a single lever that swings up and sideways to mix hot and cold, it has a cartridge, usually a ceramic or a ball type.

This split is worth understanding because it explains why the internet disagrees with itself about taps. Compression taps have been made since the middle of the nineteenth century and rubber washers were the only sealing method available for most of that time. Ceramic discs arrived in household taps in the 1980s and now dominate new fittings, because two polished ceramic plates sliding across each other have almost nothing to wear out. Advice written for one era is useless in the other.

There is also a clue in where the water appears. Water dripping from the spout means the valve is not sealing. Water seeping out around the base of the handle when the tap is running means the O ring or the gland packing has failed, which is a different part and a different fix.

What you need, and what you can skip

For a compression tap: an adjustable spanner, a flat screwdriver, a small terminal screwdriver for the handle screw, and a washer. For a ceramic or cartridge tap: an adjustable spanner, an Allen key set, and the replacement cartridge, which you buy after removing the old one and matching it, not before.

Buy a mixed washer pack rather than a single size. A pack of twenty costs around 3 pounds and covers 12.7mm and 19mm, the two sizes that fit most domestic taps. You will use one and keep the rest for years. A tap reseating tool is sold alongside these and I have only needed one twice, so leave it until you know the brass seat is pitted.

Skip the sealant. Nothing in a tap valve should be glued, and anyone selling you a tube for this job is selling you a problem for next year.

Fixing a compression tap

  1. Turn off the supply. Look under the sink for a small isolation valve on the pipe, a brass fitting with a slot you turn 90 degrees with a flat screwdriver. If there is none, close the main stopcock, usually under the kitchen sink or near the front door.
  2. Open the tap and let it drain. Then put the plug in. This is the step people skip, and a dropped screw into an open drain adds an hour to the job.
  3. Get the handle off. There is usually a small cap on top, either a screw cover you prise with a fingernail or an index disc marked hot and cold that unscrews. Under it is a retaining screw.
  4. Unscrew the headgear. This is the brass body under the handle, and it takes a 19mm or 21mm spanner. Hold the tap body steady with your other hand so you are not twisting the whole fitting on the sink.
  5. Swap the washer. At the bottom of the headgear is a rubber disc held by a small nut or just pushed on. Pull it off, note the diameter, fit the new one flat. Flat matters more than tight.
  6. Check the seat while you are in there. Run a fingertip around the brass ring the washer presses against. If it feels gritty or scored, that roughness will chew the new washer within months and you need a reseating tool or a new tap.
  7. Reassemble and open the supply slowly. Then run the tap for a minute to clear air and grit.

If it still drips after this, the headgear thread is probably worn and the whole headgear needs replacing. Those cost about 8 pounds a pair and swap in with the same spanner.

Ceramic and cartridge taps

These rarely drip, and when they do it is almost never a washer. The ceramic discs crack from a grit particle that got past them during building work or a mains repair, or the rubber seal on the base of the cartridge hardens.

The procedure is similar but the parts are less generic. Remove the handle, which on a single lever mixer usually hides a tiny Allen screw behind the blue and red indicator plate. Unscrew the brass retaining ring. Lift out the cartridge and measure its diameter at the top, commonly 25mm, 35mm or 40mm. Take the old cartridge to the shop. Photographs are not enough, because two cartridges that look identical can have the splines in different positions.

One thing worth trying before buying anything: lift the cartridge, rinse it under a running tap, work the lever a dozen times, and refit it. Grit is a common cause and this clears it maybe one time in four.

Tightening it harder is how taps get destroyed

The most common piece of advice about a dripping tap, usually from someone standing nearby, is to turn the handle harder. It works, briefly. It is also the single fastest way to turn a 60 pence repair into a new tap.

On a compression tap, forcing the handle compresses the rubber washer past its elastic limit, so it takes a permanent dish shape and seals even less well next time. Worse, it drives the washer against the brass seat hard enough to leave a ring in the softer brass. Once that ring exists, no washer will seal, and you are into reseating or replacement.

On a ceramic tap it is more direct. The handle has a hard stop by design, and pushing past it strains the plastic spline on the cartridge stem. I have seen a kitchen mixer where the lever spun freely in both directions because someone had sheared the spline in exactly this way, over about six months of impatient closing.

The honest version is that a tap should close with two fingers. If it needs a fist, something inside has already failed and the force is hiding the symptom rather than fixing it. The same logic shows up in other household repairs, including the one in how to fix a running toilet, where forcing a flapper to sit flatter never lasts.

When it is not the tap at all

Two cases look like a dripping tap and are not. The first is a drip that appears only after you have run hot water, then stops. That is usually expansion in an unvented hot water system pushing a little water past the valve as the cylinder heats, and it needs the expansion vessel checked rather than a washer.

The second is white crust around the spout with a slow weep through it. That is limescale holding the outlet open, and in hard water areas it is common. Descaling the aerator fixes it and the method is the same one used on kettles, described in how to descale a kettle. If the scale has built up around the handle and base as well, removing limescale from taps covers the safe way to do it without scratching the chrome.

Call a plumber if the isolation valve will not close, if the tap body itself is cracked, or if you cannot find a stopcock. A call out runs somewhere around 80 to 120 pounds in most of the UK, which is still cheaper than a flooded kitchen floor.

FAQ

How much water does a dripping tap waste?

About 15 litres a day at one drip per second, so roughly 5,500 litres a year. A steady trickle rather than a drip can reach ten times that. On a water meter the cost is modest, around 15 pounds a year, which is why most people fix it for the noise rather than the bill.

Can I fix a dripping tap without turning off the water?

No. The valve you are opening is what holds back mains pressure. Find the isolation valve under the sink or close the main stopcock first, then open the tap to drain the standing water in the pipe.

Why does my tap still drip after a new washer?

Usually because the brass seat the washer presses onto is pitted or has a ring worn into it, so the new washer cannot make full contact. Feel the seat with a fingertip. If it is not smooth, you need a reseating tool, a new headgear, or a new tap.

How long should a tap washer last?

Five to ten years in soft water and often three to five in hard water, assuming the tap is closed gently. Closing it with force shortens that dramatically, sometimes to a single season.

LF
Lena Fischer

Lena digs into the meanings and backgrounds behind the questions people ask, explaining them plainly and without fuss.

More posts by Lena

More in Home

01doorganico 084goad 3hot8 4465456 after5internprogram ahandfulofblessings ahmadpc ahomcybersecurity allodialresources annodex antiquesandperiodcollectibles aotc asianworldkashmir beedlectrics bloggertemplatefree bluefeatheragency bodyweightsolution campaign08blog carfixadvisor catstreetcollective cbstvsports cnfanspurchasing committeeof500yearsofdignityandresistance covertopsdjs cs-kaiyuangame cuestacomunicaciontotal cxoutlet dancebetgame deskgearhub destinyvillastay detectmagazine di33 diamondsteelbuildings donmo dyanadropship emarsysfinance emimattl escapechan eskitarih evautoplay everythingweddings-orlando farmzone feedviewerapp foxstudiosscratch gamevui123 gleasongrade greetingsday hacklabasu haskell iw-kaiyun jagoanproperti jilidskripsi joltbusinessfinance juegodepokergratis juegospucca kaeru-festival latestmehndidesigns lestanzediottaviano localcommunityhero lustrsazan mariashebets menswheels newwebstechs1 nikkit ootheday oxigenvpn plurfitness prefetial probudgetcarpetcleaning psychicmrsmartin pyaten qvantor rejoignezlogis rexzbot riselayouts ruchin rwxqsgd5 sakaltime shibiaowang shop-bot skrtips spotlesshaven strcoding tetapatrium topselller uneplanteartificielle vipertechcr webtech1223411 wo-kygaming yamaha-mekar yeknava yoybuysheets zenunwa yamaha-mekar jilidskripsi ankertoto ankertoto ankertoto ankertoto